View A060SE02-V9_7669018.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

customer approval sheet company name model a060se02 v9 customer approved approval for specifications only (spec. ver. 0.2) approval for specifications and es sample (spec. ve r. 0.2) approval for specifications and cs sample (spec. ve r. 0.2) customer remark : auo pm : rodin huang p/n : 94.06a15.900 comment : 1 li-hsin rd. 2. science-based industrial park hsinchu 300, taiwan, r.o.c. tel: +886-3-500-8899 fax: +886-3-577-2730
all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. doc. version : 0.2 total pages : 23 date : 2011/1/27 product specification 6" epd module model name a060se02 v9 planned lifetime: from 2010/aug. to 2011/ aug. phase-out control: from 2011/may. to 2011/ aug. eol schedule: 2011/ aug. < >preliminary specification < >final specification note: the content of this specification is subject to change. ? 2010 au optronics all rights reserved, do not copy.
version: 0.2 page: 1 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. record of revision version revise date page content 0.0 2010/11/9 all first draft. 10 update absolute max rating spec 22 modify application note. 0.1 2010/11/25 26 update application circuit 0.2 2011/01/27 4 update outline dimension, changing label position .
version: 0.2 page: 2 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. contents a. general information ...........................................................................................3 b. outline dimension .............................................................................................4 c. electrical specifications .....................................................................................5 1. pin assignment ...................................... ................................................... ................................................... ....5 2. absolute maximum ratings ............................ ................................................... ............................................9 3. operation ratings .................................. ................................................... ................................................... ....9 d. electrical characteristics ..................................................................................10 1. panel power consumption............................ ................................................... .............................................10 e. input timing ac characteristics .....................................................................11 1. horizontal input timing............................ ................................................... ................................................11 1.1 relationship of input data and source output vol tage............................................... .......................12 2. vertical input timing ............................... ................................................... ..................................................1 3 3. vcom voltage definition ............................ ................................................... .............................................14 4. vcom relationship ................................... ................................................... ................................................14 f. power on/off characteristics .........................................................................15 1. recommended power on/off sequence.................... ................................................... ..............................15 g. optical specification ........................................................................................16 h. reliability test items........................................................................................18 i. packing and marking .......................................................................................20 1. packing form ....................................... ................................................... ................................................... .....20 2. module/panel label information..................... ................................................... .........................................21 3. carton label information........................... ................................................... ................................................21 j. application note ...............................................................................................22 1. application circuit............................... ................................................... ................................................... ....22 k. precautions .........................................................................................................23
version: 0.2 page: 3 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. a. general information this display is a active matrix electrophoretic dis play (epd), which comprises a-si tft substrace, electrophoretic front plane, protective anti-glare top-sheet, driver ics, and fpc. it is designed for applications such as e-book or e-reader. no. item unit specification remark 1 screen size inch 6 (diagonal) 2 display resolution dot 800 (h) 600 (v) 3 overall dimension mm 130.4 (h) 104.6 (v) 1.32 (t) note 1 4 active area mm 122.4 (h)90.6 (v) 5 dot pitch mm 0.153 (h)x 0.151 (v) 6 gray level -- 16 7 weight g (30.6) 8 surface treatment ag (7.5 2%) hard coating (3h) note 2 note 1: not include fpc. refer next page to get fur ther information. note 2: 750 g load force on uni/jpia 3h pencil, spe ed is 3.5mm/s on the ag film and scratch length is 1cm and write 5 handwriting, scratch no. Q 2 is ok
version: 0.2 page: 4 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. b. outline dimension
version: 0.2 page: 5 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. c. electrical specifications 1. pin assignment recommended connector : fh12-50s-0.5sh. pin no. symbol i/o i/o structure description remark 1 dummy -- -- dummy pin 2 vcom o -- vcom polarity output signal 3 vcom_bot i -- vcom signal setting pin 4 vcomdc p type2 external voltage for vcomdc power. 5 vcomh p -- external voltage for vcom high power. 6 vcoml p -- external voltage for vcom low power. 7 rst_n i type 3 global reset pin. low reset. 8 shd_n i type 3 dc-dc converter shut down pin. 0 : enable.(panel shut down; default ) 1 : disable. 9 pwr_rdy o type 1 power ready output. when shd_n from 1 to 0: pwr_rdy will become 0 . when shd_n from 0 to 1: after 100ms, pwr_rdy wi ll become 1. note1 10 vcomin_0 i type 2 logic input for vcom voltage generate. 11 vcomin_1 i type 2 logic input for vcom voltage generate. 12 yoe i type 3 vertical output enable pin. note2 13 yclk i type 3 vertical clock. input note2 14 ud i type 3 vertical (up/down) scan direction. u/d = "l": shift up to down. default u/d = "h": shift down to up.
version: 0.2 page: 6 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 15 ydiod i/o type 5 16 ydiou i/o type 5 vertical start pulse input/output. these pins are used to input and output shift data. these pins are switched as input or output by setting the ud pin as follow. ud ydiou ydiod l output input h input output 17 xdiol i/o type 5 18 xdior i/o type 5 horizontal start pulse input/output. these pins are used to input and output shift data. these pins are switched as input or output by setting the shl pin as follow. shl xdiol xdior l input output h output input 19 ld i type 3 latch data. 20 d0 i type 3 data input, first pixel lsb 21 d1 i type 3 data input, first pixel msb 22 d2 i type 3 data input, second pixel lsb 23 d3 i type 3 data input, second pixel msb 24 d4 i type 3 data input, third pixel lsb 25 d5 i type 3 data input, third pixel msb 26 d6 i type 3 data input, forth pixel lsb 27 d7 i type 3 data input, forth pixel msb 28 shl i type 3 horizontal (left/right) scan direction. shl = l: shift right to left. shl = h:shift left to right. default 29 xclk i type 3 horizontal clock input.. note3 30 vref c -- for power setting capactor connected pin. 31 vr p -- vcomdc reference voltage 32 avdd c -- for power setting capactor connected pin. 33 c1p c -- for charge pump capactor connected pin. 34 c1n c -- for charge pump capactor connected pin. 35 vss p -- digital ground 36 vssa p -- analog ground. 37 vdd p -- analog power. 38 vref_pos c -- for power setting capactor connected pin. 39 vref_neg c -- for power setting capactor connected pin.
version: 0.2 page: 7 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 40 vddx8 p -- dcdc positive voltage 41 nvddx8 p -- dcdc negative voltage 42 vdd_drv p -- dcdc power. 43 adrvu o type 1 pwm output for dcdc converter. 44 adrvd o type 1 pwm output for dcdc converter. 45 vss_drv p -- dcdc ground. 46 vdps p -- external voltage for source postive power. 47 vdns p -- external voltage for source negative power. 48 vdpg c -- for power setting capactor connected pin. 49 vdng c -- for power setting capactor connected pin. 50 dummy d -- dummy pin i: input pin; o:output pin, i/o: input / output; p: power pin; c: capacitor pin; d dummy note 1: please reference chapter f note 2: please reference chapter e note 3: please reference chapter e
version: 0.2 page: 8 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. i/o pin structure:
version: 0.2 page: 9 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. absolute maximum ratings item symbol condition min. max. unit remark power voltage vdd vssa=vss=0 -0.3 +5.0 v power voltage vdd_drv vss_drv=0 -0.3 +5.0 v vdps vssa=vss=0 +20 v source voltage vdns vssa=vss=0 -20 v vdpg vssa=vss=0 -0.3 vdng+40 v gate voltage vdng vssa=vss=0 vdpg-40 +0.3 v vcomh vssa=vss=0 0 vnpg-1 v vcom voltage vcoml vssa=vss=0 vdng+1 0 v storage temperature tstg - -25 70 operating topa - 0 40 3. operation ratings item symbol min. typical max. unit remark power voltage vdd=vcc 3.0 3.3 3.6 v power voltage vdd_drv 3.0 3.3 3.6 v vdps 14.5 15 15.5 v source voltage vdns -15.5 -15 -14.5 v vdpg 19 20 21 v gate voltage vdng -21 -20 -19 v vcomh 10.5 11 11.5 v vcom voltage vcoml -19.5 -19 -18.5 v
version: 0.2 page: 10 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. d. electrical characteristics 1. panel power consumption item symbol condition min. typical max. unit vdd vssa=vss=vss_drv=0v -- 3.3 -- v supply voltage vdd_drv vssa=vss=vss_drv=0v -- 3.3 -- low level input voltage vil digital input pins gnd - 0.3xvdd v high level input voltage vih digital input pins 0.7xvdd - vdd v operating temperature t op - 25 - c vdd=vdd_drv=3.3v -- 1.07 2 ma vdns=-15v 0.82 1.5 ma vdps=15v 0.86 1.5 ma vdpg=20v 1.23 2 ma vdng=-20v 0.66 1.5 ma vcomh= 11v 0.36 1 ma operation power dissipation p vcoml= -19v 0.56 1 ma vdd=vdd_drv=3.3v -- 0.06 0.15 ma vdns=0v 0.02 0.1 ma vdps=0v 0.02 0.1 ma vdpg=3.3v 0.02 0.1 ma vdng=0v 0.02 0.1 ma vcomh=0v 0.01 0.1 ma standby power dissipation p vcoml=0v 0.02 0.1 ma t=25 -- 950 1010 ms t=10 -- 2310 2450 ms image update time t=0 -- 2750 3150 ms *: typical power consumption measured by following pattern
version: 0.2 page: 11 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. e. input timing ac characteristics 1. horizontal input timing figure 1: ld input timing n=800 figure 2: horizontal data input timing
version: 0.2 page: 12 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. (vdd=vdd_drv=3.3v, vssa=vss=vss_drv=0v, ta=25 ) parameter symbol min. typ. max. unit clock pulse width t wxdclk 13 ns data setup time t setup 2 - - ns data hold time t hold 2 - - ns ld pulse width t wld 1 - - xclk time from ld to xdiol/xdior t ld_dio 5 - - xclk 1.1 relationship of input data and source output vo ltage the source driver output voltage will base on input 2 bits data, and the relationship is as below: msb lsb function 0 0 source output is 0v 0 1 source output is vdps(+15v) 1 0 source output is vdns(-15v) 1 1 source output is floating
version: 0.2 page: 13 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. vertical input timing n=600 figure 3: vertical input timing
version: 0.2 page: 14 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 3. vcom voltage definition the vcom output voltage will base on input pins vco min[1:0], and the relationship is as below: vcomin[1 :0] function 00 vcom output is (-vdc) v 01 vcom output is (vdps-vdc) v 10 vcom output is (vdns-vdc) v 11 vcom output is floating 4. vcom relationship vcom will change while vocmin change source output will change while ld signal falling e dge.
version: 0.2 page: 15 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. f. power on/off characteristics 1. recommended power on/off sequence the suggested power on/off sequence is below: 1.1 power on sequence: 1.2 power off sequence:
version: 0.2 page: 16 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. g. optical specification all optical specification is measured under typical condition (note 1, 2) item symbol condition min. typ. max. unit remark reflectance r white 28 30 -- % note1,2,3,4 contrast ratio cr at optimized viewing angle 5 6 -- note1,2,3,5 update time t t=25 t=10 t=0 -- 950 2310 2750 1010 2450 3150 ms note 3 note 1. ambient temperature =25 note 2. reflectance and constrast ratio are measure d by konica minolta spectrophotometer cm-2600d. note 3: the measurement shall be conducted under au o specificed driving condition, including lut and tcon codes.
version: 0.2 page: 17 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 4. definition of reflectance: the reflectance is expressed as: r = reflectance factor white board x (l center / l white board ) l center is the luminance measured at center in a white are a. l white board is the luminance of a standard white board. note 5. definition of contrast ratio: the contrast ratio (cr) is the ratio between the re flectance in a full white area (rl) and reflectance in a dark area (rd). rd rl (cr) ratio contrast =
version: 0.2 page: 18 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. h. reliability test items test condition condition remark 1 high-temperature operation tamb=+40 , rh=30% for 240hrs iec 60068-2-2bp update pattern four times per minute. 2 low-temperature operation tamb=0 for 240hrs iec 60068-2-2ab update pattern four times per minute. 3 high-temperature storage tamb=+70 , rh=23% for 240hrs iec 60068-2-2bp 4 low-temperature storage tamb=-25 for 240hrs iec 60068-2-2ab 5 high-temperature, high-humidity operation tamb=+40 , rh=90% for 168hrs iec 60068-2-3ca update pattern four times per minute. 6 high-temperature, high-humidity storage tamb=+60 , rh=80% for 240hrs iec 60068-2-3ca 7 temperature cycle 1 cycle [-25 c 30min] [+70 c 30min] 100 cycles iec 60068-2-14 8 uv exposure resistance condition: 1120w/m2, 40 test duration: 3 cycles (definition of 1 cycle: 8 hr at exposure state and 16 hr at non-exposure state) iec 60068-2-5sa 9 package vibration 1.04g, frequency 10 ~ 500hz direction x, y, z duration 1 hours in e ach direction 10 package drop impact drop from height of 100 cm on concrete surface. drop sequence 1 corner, 3 edges, 6 faces one drop for each. 11 electrostatic discharge air-mode : +/- 6kv contact-mode : +/- 2kv iec 61000-4-2 12 fpc bonding strength pull the fpc stiffener part with a force of 500gf in the horizontal and vertical directions
version: 0.2 page: 19 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 13 fpc bending performance apply mit method. bending rate radius 1.0mm weight 500gf, bending angle 135 bending cycle 20 times 14 stylus tapping polyacetal pen top r0.8mm load 300gf speed 3 times/sec total 13,500 times pass criteria - no glass breakage or damage to micro-cups. note 1. in the above conditions, there is no displa y function ng issue occurred. all the cosmetic spec ification is judged before the reliability stress. note 2. the test modules will be kept at 25 environment for 4 hours after finish the environme ntal test and make measurement after auo specified tcon code and waveform re-driving. the judgement of above tests should satisfy minimum contrast ratio and minimum r eflectance. note 3. for item 8, in addition to satisfy minimum contrast ratio and minimum reflectance, the display shall be able to identify 8 gray levels, including black and white when being driven under auo specified drivin g condition at the end of test. note 4. esd testing method. 1. ambient: 24~26 , 56~65%rh, atmospheric pressure : 940~960hpa 2. instruments:noisekeness-2000, 3. operation system: auo pattern generator 4. test mode: non-operating mode, test pattern: che ss 5. test method: a. contact discharge: 150pf(330 ) 1sec, 5 points, 10 times/point b. air discharge: 150pf(330 ) 1sec, 5 points, 10 times/point 6. test point:
version: 0.2 page: 20 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. i. packing and marking 1. packing form
version: 0.2 page: 21 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. module/panel label information the module/panel (collectively called as the produ ct) will be attached with a label of shipping number which represents the identification of the product at a specific location. refer to the product outline drawing for detailed l ocation and size of the label. the label is composed of a 22-digit serial number and printed wi th code 39/128 with the following definition: 3. carton label information the packing carton will be attached with a carton l abel where packing qty, auo model name, auo part number, customer part number (optional) an d a series of carton number in 13 or 14 digits are printed. the carton number is appari ng in the following format: refer to the drawing of packing format for the loca tion and size of the carton label.
version: 0.2 page: 22 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. j. application note 1. application circuit
version: 0.2 page: 23 / 23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. k. precautions 1. do not twist or bend the module and prevent the unsuitable external force for display module during assembly. 2. adopt measures for good heat radiation. be sure to use the module with in the specified temperature. 3. avoid dust or oil mist during assembly. 4. follow the correct power sequence while operatin g. do not apply the invalid signal, otherwise, it will cause improper shut down and damage the mod ule. 5. less emi: it will be more safety and less noise. 6. please operate module in suitable temperature. t he response time & brightness will drift by different temperature. 7. be sure to turn off the power when connecting or disconnecting the circuit. 8. display surface never likes dirt or stains. 9. a dewdrop may lead to destruction. please wipe o ff any moisture before using module. 10. high temperature and humidity may degrade perfo rmance. please do not expose the module to the direct sunlight and so on. 11. acetic acid or chlorine compounds are not frien ds with display module. 12. static electricity will damage the module, plea se do not touch the module without any grounded device. 13. do not disassemble and reassemble the module by self. 14. be careful do not touch the rear side directly. 15. no strong vibration or shock. it will cause mod ule broken. 16. storage the modules in suitable environment wit h regular packing. 17. be careful of injury from a broken display modu le. 18. please avoid the pressure adding to the surface (front or rear side) of modules, because it will cause the display non-uniformity or other func tion issue. 19. application under direct sunlight is strongly not r ecommended as it would result in display performance degradation. 20. it is highly recommended that the display is expose d to an even lighting condition to ensure a good display uniformity. 21. elimination of light exposure to the display by applying proper means, e.g. lighting shielding cover is suggested when the display is not being us ed to extend the life performance of the device. 22. heat isolation or heat sink to control uniformi ty of panel temperature should smaller than 3 23. any performance degradation or display distorti on which can be eliminated by display refreshing should not be regarded as a defect.

▲Up To Search▲

Price & Availability of A060SE02-V9

	To Download A060SE02-V9 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .